"industrial centrifugal blower"

Ventilateur centrifuge haute pression pour le transport de gaz. Gère une pression de 2705 à 15 425 Pa, un débit de 3 297 à 63 305 m³/h. Personnalisable avec des moteurs haut de gamme (ABB/Siemens), des matériaux résistants à la corrosion/à l'usure. Optimisé par CFD pour l'efficacité énergétique. Garantie 1 an avec assistance à l'installation.

Long Life Single Inlet Building Ventilate High Pressure Centrifugal Fan Introduction The 9-10.19 series centrifugal fan can output high gas pressure, suitable for conveying normal or high temperature clean gas/combustible gas/corrosive gas/mixed with a few impurities, light particles/debris/short fiber materials. The most commonly used for forced ventilation, rapid drying, rapid cooling and heat dissipation, cement production line chiller cooling, clinker cooler, circulating

Single Suction Backward Solid Waste And Hazardous Waste Treatment Industry Blower Introduction The 6-06 series dust exhaust centrifugal fan has the characteristics of low dust accumulation and wear resistant. It is suitable for discharging gas containing dust, wood chips and finely divided fibers (If it contains hard particles, a dust removal device must be installed in front of the fan.), it can also be used as a general ventilator for ventilation. Application Centrifugal

Air Supply Backward High Pressure Forced Draught Centrifugal Fan Introduction The 10-06 series high-pressure centrifugal fan is a new product developed by QingHua University for blowing coal powder into the boiler. This series of products has the advantages of high efficiency, wear resistance, flat performance curve, wide efficiency range, low price, etc. Small fertilizer plant production support, can also be used in high-pressure forced ventilation of iron furnace, burning

Aluminium Alloyed Energy Efficiency Smelting Furnace Centrifugal Flow Fan Introduction The 9-10 series high pressure fan is generally used for forging furnace and high pressure forced ventilation and widely used for material transportation. It is suitable for conveying air and non-corrosive, unnatural and non-viscous gases. The temperature of the medium is generally not more than 80°C, and the dust and hard fine particles contained in the medium are not more than 150mg/m3.

Anti Abrasive Forced Ventilating Anticorrosive And Explosion-Proof Fan Introduction These series ventilation and induced draft fans are suitable for the ventilation and induced draft fan systems of 2~670T/h steam boilers in thermal power plants. It can also be used for mine ventilation and general ventilation without other special requirements; Mainly used to meet the needs of large air flow applications, low noise and high efficiency. They can transport clean gas, dusty gas,

Medium Pressure Steam Boiler High Temperature Centrifugal Fan Blower Introduction Medium requirements for 6-08 series fans: The medium to be transported should be non-corrosive, non-flammable, explosive, and free of viscous substances. The dust and hard particles contained in the medium should be no more than 150mg/m3. Medium temperature: The medium temperature of standard fans is not more than 80 °C, the V-belt driving type fan can transport media below 150 °C for a long

Flue Gas Dilution Fan Dilution Air Fan Dilution fan_Ammonia dilution fan desulfurization system The function of dilution fan Dilution fan The dilution fan dilutes the ammonia gas to a certain ratio and sprays it into the flue of the reactor to prevent the mixture of ammonia gas and air from reaching an explosive ratio, thereby causing danger. Each unit is equipped with two dilution fans, one conveyor and one backup. Dilution fan test run and chain protection Generally, the

Ventilateur d'appoint à économie d'énergie pour le traitement des fumées. Gère un volume d’air de 16 150 m³/h, une pression de 5 500 Pa à 330°C. Matériaux personnalisables (acier au carbone/304/316), tensions et tailles. Comprend des roulements SKF/FAG durables avec une garantie d'un an.